Solar cell
This page is under construction!!!
Intro
A solar cell is a complex device with many details under the hood. Studying a solar cell, optimizing the efficiency is high tech.
Deep Basics
The energy emerging from a solar cell is an effect which can be described with quantum mechanics. This means that it is complicated!
There is a very good lecture course online: [1]
Important figures and ideas which can be discovered in this course are:
The integrated power delivered on the surface of the Earth is 100 mW/cm2
But only wavelength shorter than 1.1Ev are absorbed: so this means only 44 mW/cm2 is possible at best. Why not "all" energy can be used is a quantum effect: this has to do with discontinuity in absorbing energy. Electrons, which catch the energy or send it out again do this in "jumps", not in a nice variable way.
Irradiance
Irradiance is the power delivered at a certin spot of the world at a certain time of year. This is the maximum of the possible energy to be harvested from a solar cell. Tables can be found at this page: http://solarelectricityhandbook.com/solar-irradiance.html
MPPT relation
The energy delivered by a solar cell comes in a very specific form. Understanding this form helps with chosing the right solar cell.
Indications are given in the properties of the solar cell, like Voltage and Watt. But also these indications must be understood. These properties Voltage and Watt are most efficient values. Most of the time the efficiency is less.
- Examples:
Description from this site:
The cell is sensitive to a wide range of light wavelengths (430-1100nm), so it should produce power in a number of different settings. The rated open circuit voltage is 350mV (900nm, 1mW/cm2 light source), and short circuit current is 47μA. Angle of half sensitivity: phi = ± 65°.
open circuit voltage is 350mV
short circuit current is 47μA
First remark: you never get these two values together, so this is not Ohms law, neither the Power law!
Description from this site:
This unit is rated for 8V open voltage and 650mA short circuit. We actually took a random unit outside and measured 9.55V open voltage and 550mA short circuit.
open circuit voltage is 8V
short circuit current is 650mA
- Voltage
Indicated solar cell voltage is a maximum. At this maximum (open circuit voltage) there is not current! No current means no energy. So normally the voltage is lower. Under circumstances of the wheather, clouds, the volatge will vary - it is not stable at all.
Say we have a stable illumination.
From these examples you can see that the voltage is having a maximum. The voltage needed by a microcontroller is also fixed in a range with a minimum and a maximum. The delivered voltage from two equal cells in series can be the sum of these voltages but only if the illumination is the same. The current can even be running backwards. Extra protection can be needed (diodes) to prevent this backward current. In case of a large chain of cells the whole efficiency can deteriorate by a "bad" cell. So pratical context is very important.
Say we have a varying illumination.
For this situation, which is occuring quite often, or in case of morning and evening situations there are special chips, which can deliver a stable voltage even if the voltage of the cell is lower. For chargers this is important because they only function with a specific voltage.
- Current
The indicated current is running with no voltage (short circuit current). This means that no energy is generated at this current.
Normally the current is lower.
- Watt
The number of Watts is multiplying the maxium voltage with the maximum current. So this numbers of Watts is never attained. The real value of energy is depending on the maximum in the power point relation. Keeping the voltage and current this maximum is one of the technical difficulties of working with solar power. If the voltage is not at this maximum can mean losing 30% of the possible energy.
The second lecture: [2] teaches the deep mechanisms behind the MPPT relation.
- MPPT Graph Shape
The red dots are obtained multiplying the voltage (x axis) by the current at this voltage, green dots.
You can see that the maximum voltage for this cell, around 5V, is not generating the maximum power, which is at 3.8V.
WIth the load (resistance) in the circuit, you have to keep the cell at this maximum power point.
- Measuring the MPPT graph
Measuring the MPPT relation is not simple in practice. You need to insert the cell in a circuit in which you can vary the resistance. You need to measure the current and the voltage around the solar cell. You have to register the Voltage and the Current depending on the resistance in the circuit varied with a potmeter. Than you multiply the current and the resistance to get the power and plot the values as function of the voltage.
I solved this by using an Arduino, the analog PIN can measure voltages up to 5.0V. The current was measured using a shunt and over this shunt a Instrumental Amplifier [3]. This value can also be recorded with an analog PIN of the Arduino.
The values measured were send to a Processing Sketch which produces the graph of all the values, while you turn the potmeter.
Github Script
Energy Harvesting Chips
For harvesting there are many different situations and domains. For many of these domains Linear Technology has specialized chips.
We have used two of these:
piezo harvesting (buck circuit) LTC3588
solar harvesting (boost circuit) LTC3105
- Buck1: LTC3588: This circuit takes care of positive/negative varying voltage input (piezo).
For the connaisseur: this LTC3588 is a buck circuit (not a boost) because the Piezo produces lots of Volts (eg 14V). These Volts must be DC-DC-ed downwards to 3.3V.
I bought the LTC3588 from Farnell, but I had to solder the connections with a magnifying glass. You need an inductor and some capacitors to go with it.
You can also buy it at Sparkfun on a board: [4]
The chip can be used to harvest energy to a certain point, at which a microcontroller can be waked up from sleep mode. Then you have a bit of energy to do something before going into sleep mode again. You can send a sensor value with a transceiver for example.
This is a movie where a LED is on after waking up, then going to sleep again:
[5]
- Boost: LTC3105, for solar cell's
This IC takes care of the nuisance of clouds in front of the Sun: once started it stays on producing the set voltage between 1.2 and 7V by using a boost circuit. MPPT is functioning on a preset voltage. There is also power to feed a Attiny85.
(MPPT stands for Maximum Power Point Tracking and tries to reach the optimal energy point in exploiting solar cells.
This is an important video explaing the use of the harvesting MPPT IC’s: [6]
You cannot buy this chip at Sparkfun’s. I bought it at farnell:
[7]
like the ltc3588, and i have soldered it using a magnifying glass and made my own board:(again, add one inductor and a few caps, besides two potmeters)
as you can see there is an attiny85 attached which can indicated if the power provided is sufficient for the chip to function (amongst others).
Page with all the harvesting chips from Linear technology:
[8]